You're reading the documentation for an older, but still supported version (GL013300).
For information on the latest version, please have a look at GL013301.

torque_rt

This function performs real-time motor torque control from an external controller. It allows direct torque streaming to each joint motor through UDP-based real-time communication. This mode is typically used for advanced control algorithms such as impedance, admittance, or gravity-compensated torque feedback.

Definition
DRFLEx.h within class CDRFLEx, public section (line 604)

bool torque_rt(float fMotorTor[NUM_JOINT],
               float fTargetTime) {
    return _torque_rt(_rbtCtrlUDP, fMotorTor, fTargetTime);
};

Parameter

Parameter Name	Data Type	Default Value	Description
fMotorTor	float[6]		Target motor torque [Nm].
fTargetTime	float		Target interpolation duration [s].

Note

• Asynchronous command.

• The internal controller interpolates the torque profile to reach fMotorTor over fTargetTime.

• If fTargetTime ≤ controller cycle (~1 ms), the command is executed immediately without interpolation.

• If the next command is not received before reaching the target torque,
  the last torque input is maintained.

• If no command is received for 0.1 s, a timeout error occurs and motion stops automatically.

Caution

• In H-series robots, the second joint has a built-in gravity compensator.
  The commanded torque and the compensator’s torque are summed internally to generate motion.
  Therefore, when sending external torque commands,
  users should compensate using the relationship:
  

  \(gravity\_torque = (link\_gravity\_torque - gravity\_compensator\_torque)\)

• Excessive or unstable torque commands may cause unexpected motion.

• It is recommended to use soft torque feedback or compliance control to ensure safe response.

Return

Value	Description
1	Success — torque command applied.
0	Error — invalid argument or communication failure.

Example

#include "DRFLEx.h"
#include <iostream>
#include <cstring>
using namespace DRAFramework;

int main() {
    CDRFLEx drfl;
    drfl.connect_rt_control("192.168.137.100", 12347);

    std::string version = "v1.0";
    float period = 0.001f;  // 1 ms
    int lossCount = 4;

    // Configure real-time streaming
    drfl.set_rt_control_input(version, period, lossCount);
    drfl.set_rt_control_output(version, period, lossCount);
    drfl.start_rt_control();

    float fMotorTor[6] = {0.f, 0.f, 0.f, 0.f, 0.f, 0.f};
    float fTargetTime = 0.01f; // 10 ms

    float q[6] = {0.f};
    float q_dot[6] = {0.f};
    float q_ddot[6] = {0.f};
    float trg_q[6] = {0.f};
    float trg_q_dot[6] = {0.f};
    float kp[6] = {1.0, 1.0, 1.0, 1.0, 1.0, 1.0};
    float kd[6] = {1.0, 1.0, 1.0, 1.0, 1.0, 1.0};

    while (true) {
        // Simulated time increment
        float time = 0.0f;

        // Get current state from real-time data
        memcpy(q, drfl.read_data_rt()->actual_joint_position, sizeof(float) * 6);
        memcpy(q_dot, drfl.read_data_rt()->actual_joint_velocity, sizeof(float) * 6);
        memcpy(q_ddot, drfl.read_data_rt()->gravity_torque, sizeof(float) * 6);

        // Simple gravity + PD torque controller
        for (int i = 0; i < 6; i++) {
            fMotorTor[i] = q_ddot[i] + kp[i] * (trg_q[i] - q[i]) + kd[i] * (trg_q_dot[i] - q_dot[i]);
        }

        drfl.torque_rt(fMotorTor, fTargetTime);

        // Condition to exit
        if (time > 5.0f) {
            drfl.stop_rt_control();
            break;
        }

        std::this_thread::sleep_for(std::chrono::milliseconds(1)); // 1 ms RT loop
    }

    drfl.disconnect_rt_control();
    return 0;
}

This example demonstrates a joint-space torque control loop using proportional-derivative (PD) feedback combined with gravity compensation.

Tips

• Use torque_rt for advanced torque-level control or compliance-based applications.

• Always monitor current joint torque using read_data_rt for feedback verification.

• Apply smooth torque transitions to avoid abrupt mechanical stress.